Feeler SVW-4113
Key Specifications
Max Spindle
Spindle Taper
Tool Capacity
x axis travel
z axis travel
table length
How much does the Feeler SVW-4113 cost?
Price estimate
We do not have a price for the Feeler SVW-4113 that we can stand behind, so we show no number. Configuration, options and installation move the final price a long way: a quote is the reliable figure.
Overview
A table 4,000 mm long and 1,100 mm wide makes the Feeler SVW-4113 the long, narrow machine of the SVW series. X travel is 4,100 mm (161.4 in). Nothing else in the lineup pairs this much length with so slim a table, which keeps the gantry span down for work that is long but not wide.
Typical candidates are linear guide bases, rails, crane and conveyor members, long weldments and extrusion dies laid end to end. Load capacity is 8 ton, twice the 4 ton of the SVW-2113 at twice the table length.
Length takes some speed away. The X rapid is 20 m/min (787 ipm), where the two shorter models on this table width reach 24 m/min. Y stays at 24 m/min (945 ipm) and Z at 20 m/min. A long table is a heavy one, and the maker supports it over the whole travel so that it does not overhang the base at the ends of the stroke.
The spindle is the series standard: 6,000 rpm, BT/DIN/CAT 50, geared through a two-speed gearbox for torque at low speed. The brackets list 8,000-15,000 rpm and #40. Z travel is 800 mm (31.5 in) or, in brackets, 1,000 mm (39.4 in). Twenty-four tools are standard with 32 or 40 available.
Full Specifications
| Parameter | Value |
|---|---|
| X Axis Travel | 4,100 mm (161.4 in) |
| Z Axis Travel | 800 (1,000) mm (31.5 (39.4) in) |
| Table Length | 4,000 mm (157.5 in) |
| Table Width | 1,100 mm (43.3 in) |
| Max Table Load | 8 ton |
| Max Spindle Speed | 6,000 (8,000-15,000) rpm |
| Spindle Taper | BT/DIN/CAT 50 (#40) |
| Rapid Traverse X | 20 m/min (787 ipm) |
| Rapid Traverse Y | 24 m/min (945 ipm) |
| Rapid Traverse Z | 20 m/min (787 ipm) |
| Tool Capacity | 24 (32/40) |
Specifications sourced from feeler.com — verified 2026-10-04
Strengths & Limitations
Strengths
- 4,000 × 1,100 mm (157.5 × 43.3 in) table for long, slim workpieces
- 8 ton table load on the narrowest SVW table
- Y rapid of 24 m/min (945 ipm)
- Full-travel table support, so the long table does not overhang
Limitations
- X rapid falls to 20 m/min (787 ipm)
- Table width of 1,100 mm rules out wide plates
- Tool magazine tops out at 40
- Y travel and spindle power are not listed here
Best For
Frequently Asked Questions
01
In working terms, X travel is 4,100 mm (161.4 in) and the table is 4,000 mm (157.5 in) long by 1,100 mm (43.3 in) wide. Overall machine length and floor space are not given in the series table.
02
The table gives 20 m/min (787 ipm) for X here and 24 m/min for the SVW-3113. Feeler does not state the reason. A longer table and its load are heavier to accelerate, which is the usual explanation.
03
BT/DIN/CAT 50 as listed, at 6,000 rpm, with #40 in brackets as the alternative that goes with the 8,000-15,000 rpm range. Feeler describes the spindle drive as fully geared with a two-speed gearbox.
04
Yes, the 4,000 mm table length allows fixtures in a row, and the total must stay within the 8 ton load. Whether the machine can be divided into two work zones for loading during the cut is not stated by the maker.
More from Feeler
Other Vertical Machining Centers (VMC)
Sharp KMA-3-CNC
DN Solutions VM 750 L
Makino SLIM5n APC
YCM D3016
Ecoca VB-1400
