Feeler SVW-4223
Key Specifications
Max Spindle
Spindle Taper
Tool Capacity
x axis travel
z axis travel
table length
How much does the Feeler SVW-4223 cost?
Price estimate
We do not have a price for the Feeler SVW-4223 that we can stand behind, so we show no number. Configuration, options and installation move the final price a long way: a quote is the reliable figure.
Overview
Four metres by two: the Feeler SVW-4223 offers a 4,000 × 2,000 mm (157.5 × 78.7 in) table, 4,200 mm (165.4 in) of X travel and a 15 ton load rating.
At this size the workpieces are usually single large items rather than batches: bases for machine tools, bolsters, large welded frames, energy-sector components. Getting such a part onto the table, levelled and clamped takes hours, so the point of a multi-face machine is that it then stays there. Feeler offers an optional automatic attachment change system for the series, described as reducing manual changeover time and minimizing machining errors. With the right heads the top, the sides and angled features are finished from one datum.
The structure is described as box-type with reinforced ribs, and the table as supported over its full travel. Each table is precision milled in several steps before assembly.
In figures: X rapid 12 m/min (472 ipm), Y and Z 15 m/min (591 ipm); spindle 6,000 rpm on BT/DIN/CAT 50 through a two-speed gearbox, or 8,000-15,000 rpm with #40 in brackets; Z travel 800 mm (31.5 in) or 1,000 mm (39.4 in); magazine 24, 32, 40 or 60 tools. The neighbouring SVW-4222 has the same load and travels on a table 1,800 mm wide.
Full Specifications
| Parameter | Value |
|---|---|
| X Axis Travel | 4,200 mm (165.4 in) |
| Z Axis Travel | 800 (1,000) mm (31.5 (39.4) in) |
| Table Length | 4,000 mm (157.5 in) |
| Table Width | 2,000 mm (78.7 in) |
| Max Table Load | 15 ton |
| Max Spindle Speed | 6,000 (8,000-15,000) rpm |
| Spindle Taper | BT/DIN/CAT 50 (#40) |
| Rapid Traverse X | 12 m/min (472 ipm) |
| Rapid Traverse Y | 15 m/min (591 ipm) |
| Rapid Traverse Z | 15 m/min (591 ipm) |
| Tool Capacity | 24 (32/40/60) |
Specifications sourced from feeler.com — verified 2026-10-04
Strengths & Limitations
Strengths
- 4,000 × 2,000 mm (157.5 × 78.7 in) table, the largest table size in the SVW series, shared with the SVW-4225
- 15 ton maximum load for single large workpieces
- Optional automatic attachment change for finishing several faces from one datum
- Box-type ribbed structure with a table supported over its full travel
Limitations
- X rapid is limited to 12 m/min (472 ipm)
- Load rating is the same 15 ton as the narrower SVW-4222
- Attachment heads, spindle power and Y travel are not listed on this page
Best For
Frequently Asked Questions
01
The table is 4,000 mm by 2,000 mm (157.5 × 78.7 in) and carries up to 15 ton. X travel is 4,200 mm (165.4 in) and Z travel 800 mm, or 1,000 mm as the bracketed alternative. Y travel is not listed on this page.
02
Nothing in the rows shown here. Both columns give the same X travel, table, load, rapids, spindle and magazine. The model numbers differ, and the Y-axis travel of each should be confirmed with Feeler before choosing.
03
Feeler names an optional automatic attachment change system that reduces manual changeover time, improves productivity and minimizes machining errors. Which heads it changes is not stated on the series page.
04
6,000 rpm for the listed geared spindle with a BT/DIN/CAT 50 taper. The bracketed alternative is 8,000-15,000 rpm with #40, a lighter spindle for higher surface speeds.
More from Feeler
Other Vertical Machining Centers (VMC)
Sharp LMV-49-DVS-MP-2
DN Solutions VM 960
Ecoca VL-1000
TRAK DPM RX3
Quaser MF400
