Litz LV-800A
Key Specifications
Max Spindle
Tool Capacity
Table Size
Spindle Power
x axis travel
y axis travel
How much does the Litz LV-800A cost?
Price estimate
We do not have a price for the Litz LV-800A that we can stand behind, so we show no number. Configuration, options and installation move the final price a long way: a quote is the reliable figure.
Overview
The Litz LV-800A is a three-axis vertical machining centre with 800 mm (31.5 in) of X travel, 500 mm (19.7 in) of Y and 540 mm (21.3 in) of Z, a 12,000 rpm BBT-40 spindle and a 24-tool arm-type changer.
The table is 910 x 500 mm (35.8 x 19.7 in), wider than the X travel, so a fixture plate can overhang the cutting range at each end. Load capacity is 500 kg (1,102 lb). Spindle nose to table distance is 150 to 690 mm (5.9 to 27.2 in), which leaves room under the nose at the bottom of the stroke for a vise and a short tool.
On the spindle side, the motor is listed as 11 / 15 / 18.5 kW (14.8 / 20.1 / 24.8 hp). 12,000 rpm suits aluminium and general steel work with small and medium cutters. A 15,000 rpm spindle, a spindle oil cooler and coolant through the spindle are all options, so a shop that needs them must order them.
Rapids are 36 / 36 / 24 m/min (1,417 / 1,417 / 945 ipm) on linear guideways, with a cutting feed range of 1-20,000 mm/min. The magazine takes tools up to 300 mm (11.8 in) long and 7 kg (15 lb); a 30T magazine is optional. Chips leave by an auger inside the machine as standard, and a chip conveyor is an extra.
The LV-800A weighs 5,500 kg (12,125 lb), draws 20 kVA and carries 240 L of coolant.
Full Specifications
| Parameter | Value |
|---|---|
| X Axis Travel | 800 mm (31.5 in) |
| Y Axis Travel | 500 mm (19.7 in) |
| Z Axis Travel | 540 mm (21.3 in) |
| Distance Spindle Nose to Table | 150 to 690 mm (5.9 to 27.2 in) |
| Max Spindle Speed | 12,000 rpm |
| Tool Capacity | 24 |
| Max Tool Diameter (full magazine) | 80 / 150 mm (3.1 / 5.9 in) |
| Max Tool Length | 300 mm (11.8 in) |
| Max Tool Weight | 7 kg (15 lb) |
| Tool Change Method | ARM |
| Tool Shank | BBT-40 |
| Spindle Motor Power | 11 / 15 / 18.5 kW (14.8 / 20.1 / 24.8 hp) |
| Axis Motors Xyz | 3 / 3 / 3 kW |
| Table Size | 910 x 500 mm (35.8 x 19.7 in) |
| Max Table Load | 500 kg (1,102 lb) |
| T-Slots | 5 x 18 x 100 mm (slot x width x center distance) |
| Rapid Traverse Xyz | 36 / 36 / 24 m/min (1,417 / 1,417 / 945 ipm) |
| Cutting Feed Rate | 1-20,000 mm/min (up to 787 ipm) |
| Machine Weight | 5,500 kg (12,125 lb) |
| Power Requirement | 20 kVA |
| Coolant Tank Capacity | 240 L |
| Compressed Air | 6 kg/cm² |
Specifications sourced from litzhitech.com — verified 2026-10-04
Strengths & Limitations
Strengths
- 12,000 rpm BBT-40 spindle with an 11 / 15 / 18.5 kW (14.8 / 20.1 / 24.8 hp) motor
- Rapids of 36 / 36 / 24 m/min (1,417 / 1,417 / 945 ipm)
- 540 mm (21.3 in) of Z travel over a 500 mm (19.7 in) Y
- 24-tool arm-type changer handling tools up to 300 mm (11.8 in) long
- Chip auger, chip cart, coolant gun and fully-covered sheet metal are standard
Limitations
- Table load is limited to 500 kg (1,102 lb)
- Coolant through the spindle and the spindle oil cooler are options
- Chip conveyor is optional; only the internal chip auger is standard
- Maximum tool weight is 7 kg (15 lb)
Best For
Frequently Asked Questions
01
X travel is 800 mm (31.5 in), Y travel 500 mm (19.7 in) and Z travel 540 mm (21.3 in). The work table is 910 x 500 mm (35.8 x 19.7 in) with a maximum load of 500 kg (1,102 lb), and the spindle nose to table distance is 150 to 690 mm (5.9 to 27.2 in).
02
Spindle speed is 12,000 rpm with a BBT-40 tool shank, and the spindle motor is listed as 11 / 15 / 18.5 kW (14.8 / 20.1 / 24.8 hp). The accessory list shows a 15,000 rpm spindle, a spindle oil cooler and coolant through the spindle as options.
03
The magazine capacity is 24 tools with an arm-type changer; a 30T magazine is optional. Maximum tool diameter is 80 / 150 mm (3.1 / 5.9 in), maximum tool length 300 mm (11.8 in) and maximum tool weight 7 kg (15 lb).
04
The accessory list marks FANUC 0iMF as the standard controller. Axis motors are 3 / 3 / 3 kW, the cutting feed range is 1-20,000 mm/min (up to 787 ipm), and the machine needs a 20 kVA supply and 6 kg/cm² of compressed air.
More from Litz
Other Vertical Machining Centers (VMC)
Mazak VTC-530C
DN Solutions MYNX 6500 50 II
Haas VF-12/40
Vision Wide NF-10023 / NF-10030
YCM TV158B
