PAMA Speedmat HP
Key Specifications
x axis travel
y axis travel
z axis travel
swing diameter
milling table size
milling table load
How much does the PAMA Speedmat HP cost?
Price estimate
We do not have a price for the PAMA Speedmat HP that we can stand behind, so we show no number. Configuration, options and installation move the final price a long way: a quote is the reliable figure.
Overview
The PAMA Speedmat HP is the five-axis member of the Speedmat family. It keeps the T-type layout, a travelling table in front of a moving column, but the headstock carries a tilting milling head with a continuous A axis, not a boring bar. PAMA lists it under five-axis machining centers and builds it in seven sizes.
Two heads are offered. The HVA head has its continuous axis inclined at 45° and a 74 kW (99.2 hp) Direct Drive spindle, listed with 609 / 286 Nm at 8,000 / 12,500 rpm. Its A axis holds 4,000 Nm (2,950 lb-ft) while contouring and 8,000 Nm (5,901 lb-ft) clamped. The AHD head is the heavier fork-type unit with a continuous tilting axis: 55 / 66 / 105 kW, 750 / 320 / 1,035 Nm and 6,000 / 12,000 / 6,000 rpm, with A axis torque of 8,000 Nm (5,901 lb-ft) contouring and 12,000 Nm (8,851 lb-ft) clamped.
Those A axis figures say a lot about intended use. A tilting axis that resists 8,000 Nm (5,901 lb-ft) in motion is meant to cut steel and titanium in full five-axis interpolation, not just to position for finishing.
The working area is smaller and quicker than the boring-bar Speedmat. Swing is 2,200 - 4,600 mm, tables are 1,000 x 1,000 - 2,000 x 2,500 mm with up to 35,000 kg, and the hydrostatic B axis turns at up to 10 rpm. Travels are 2,200 - 4,600 mm in X, 1,700 - 3,500 mm in Y and 2,000 - 3,200 mm in Z, with rapids up to 50,000 mm/min.
A milling and turning version, the Speedmat HPT, has its own column in the technical sheet. Control is Siemens, Heidenhain or Fanuc.
Full Specifications
| Parameter | Value |
|---|---|
| X Axis Travel | 2,200 - 4,600 mm |
| Y Axis Travel | 1,700 - 3,500 mm |
| Z Axis Travel | 2,000 - 3,200 mm |
| Swing Diameter | 2,200 - 4,600 mm |
| Milling Table Size | 1,000 x 1,000 - 2,000 x 2,500 mm |
| Milling Table Load | up to 35,000 kg |
| B Axis Rapid Feed | up to 10 rpm |
| Hva Headstock Transmission | Direct Drive |
| Hva Headstock Spindle Power S1 | 74 kW (99.2 hp) |
| Hva Headstock Spindle Torque S1 | 609 / 286 Nm |
| Hva Headstock Spindle Speed | 8,000 / 12,500 rpm |
| Hva Headstock A Axis Contouring Torque | 4,000 Nm (2,950 lb-ft) |
| Hva Headstock A Axis Clamping Torque | 8,000 Nm (5,901 lb-ft) |
| Ahd Headstock Transmission | Direct Drive |
| Ahd Headstock Spindle Power S1 | 55 / 66 / 105 kW |
| Ahd Headstock Spindle Torque S1 | 750 / 320 / 1,035 Nm |
| Ahd Headstock Spindle Speed | 6,000 / 12,000 / 6,000 rpm |
| Ahd Headstock A Axis Contouring Torque | 8,000 Nm (5,901 lb-ft) |
| Ahd Headstock A Axis Clamping Torque | 12,000 Nm (8,851 lb-ft) |
| Rapid Traverse Xyz | up to 50,000 mm/min |
Specifications sourced from pamamachinetools.com — verified 2026-10-05
Strengths & Limitations
Strengths
- Continuous A axis heads: HVA inclined at 45°, or AHD with a continuous tilting axis
- AHD head options up to 105 kW and 1,035 Nm, or 12,000 rpm
- A axis contouring torque of 8,000 Nm (5,901 lb-ft) on the AHD head
- Hydrostatic B axis with rapid feed up to 10 rpm and loads up to 35,000 kg
- Linear rapids up to 50,000 mm/min
Limitations
- No boring bar or W axis; deep boring belongs on the Speedmat or Speedmat RAM
- Table load of up to 35,000 kg is below the 50,000 kg of the Speedmat
- Largest table is 2,000 x 2,500 mm
- The HVA spindle's torque at 12,500 rpm is 286 Nm, so that option is for lighter cuts
Best For
Frequently Asked Questions
01
Yes. PAMA describes the Speedmat HP as a five-axis machining center. The three linear axes and the rotary table B axis are joined by a continuous A axis in the head, either the HVA head with its axis inclined at 45° or the AHD head with a continuous tilting axis.
02
HVA head: 74 kW (99.2 hp), 609 / 286 Nm at 8,000 / 12,500 rpm. AHD head: 55 / 66 / 105 kW, 750 / 320 / 1,035 Nm at 6,000 / 12,000 / 6,000 rpm. All are Direct Drive and rated in S1. The columns line up, so the 12,000 rpm AHD spindle is the 66 kW, 320 Nm one.
03
Swing diameter is 2,200 - 4,600 mm. Tables or pallets measure 1,000 x 1,000 - 2,000 x 2,500 mm and carry up to 35,000 kg. Axis travels are 2,200 - 4,600 mm in X, 1,700 - 3,500 mm in Y and 2,000 - 3,200 mm in Z.
04
The HP is the milling version with a rotary milling table. The Speedmat HPT is the multitasking version with a turning table of Ø1,250 - Ø2,500 mm that runs at up to 350 rpm. Both use the same HVA and AHD heads.
More from PAMA
Other 5-Axis Machining Centers
DN Solutions DVF 8000
DMG Mori DMF 400|11 FD
Makino a500iR
AWEA MCP-20050
