Onsrud 216GW10
Key Specifications
Max Spindle
Tool Capacity
Spindle Power
table size x
table size y
machine length
How much does the Onsrud 216GW10 cost?
Price estimate
We do not have a price for the Onsrud 216GW10 that we can stand behind, so we show no number. Configuration, options and installation move the final price a long way: a quote is the reliable figure.
Overview
The Onsrud 216GW10 combines the ten-foot table width of the wide G-Series with its two tallest strokes, 28 in (711 mm) and 40 in (1,016 mm). Table X is 216 in (5,487 mm) and table Y is 120 in (3,048 mm).
Ten feet across and forty inches up is a large volume to machine in. It suits boat and vehicle patterns cut in sections, big architectural pieces and board built up into blocks, provided the shapes can be reached from above. This is a 3-axis machine. Anything with undercuts or steep walls calls for a 5-axis head.
Onsrud gives the frame as 323 in (8,205 mm) long, 200 in (5,080 mm) wide and 167 in (4,242 mm) high for both strokes. The two-hundred-inch width means the machine needs a bay at least seventeen feet clear before walkways.
There are 5 vacuum zones as standard, the same count as the 216GW8, so each zone is wider here. One 18 hp (13.4 kW) spindle at 24,000 rpm is standard and 24 hp (17.9 kW) is optional. Tool capacity is 12, with larger changers offered. Operators run the machine from a FANUC controller or Onsrud's touchscreen interface.
Full Specifications
| Parameter | Value |
|---|---|
| Table Size X | 216 in (5,487 mm) |
| Table Size Y | 120 in (3,048 mm) |
| Machine Length | 323 in (8,205 mm) |
| Machine Width | 200 in (5,080 mm) |
| Machine Height | 167 in (4,242 mm) |
| Vacuum Zones Standard | 5 |
| Spindle Motor Power | 18 hp (13.4 kW) |
| Max Spindle Speed | 24,000 rpm |
| Tool Capacity | 12 (larger capacity tool changers optional) |
| Z Stroke | 28 in (711 mm); 40 in (1,016 mm) |
| Spindle Power Optional | 24 hp (17.9 kW) |
| Spindles Optional | Up to 4 |
| Dual Gantry | Optional |
| Second Tool Changer | Optional |
Specifications sourced from cronsrud.com — verified 2026-10-05
Strengths & Limitations
Strengths
- 120 in (3,048 mm) of table Y with up to 40 in (1,016 mm) of Z
- 216 in (5,487 mm) of table X
- Footprint is the same for the 28 in and 40 in strokes
- Larger capacity tool changers offered beyond the standard 12 tools
Limitations
- Frame width of 200 in (5,080 mm)
- Machine height of 167 in (4,242 mm)
- Three axes only: undercuts and steep walls are out of reach
Best For
Frequently Asked Questions
01
The table is 216 in (5,487 mm) by 120 in (3,048 mm), and the Z-stroke is 28 in (711 mm) or 40 in (1,016 mm). Usable part height is less than the stroke once tool length is allowed for.
02
The machine is 323 in (8,205 mm) long, 200 in (5,080 mm) wide and 167 in (4,242 mm) high. Those are the maker's frame figures for both strokes. Rigging a machine of that height into place may also need a clear route and a high door.
03
Two feet of width. The 216GW12 has 144 in (3,658 mm) of table Y and a 224 in (5,690 mm) frame. Table X, length, height, strokes and the 5 vacuum zones match the 216GW10.
04
It can rough and finish shapes that are open from above. It has 3 axes, so the tool cannot tilt into undercuts or follow steep walls with a short cutter. Onsrud's G-Series 5-Axis line is built for that.
