Ibarmia P30
Key Specifications
Tool Capacity
Spindle Power
max swing diameter
max part height
b axis range
a axis range
How much does the Ibarmia P30 cost?
Price estimate
We do not have a price for the Ibarmia P30 that we can stand behind, so we show no number. Configuration, options and installation move the final price a long way: a quote is the reliable figure.
Overview
The Ibarmia P30 sits in the middle of the P series: a 5-axis machining center with a 3,000 mm (118.1 in) maximum swing diameter and room for parts 1,950 mm (76.8 in) high. Below it the P26 is listed at 2,600 mm (102.4 in) by 1,750 mm (68.9 in), above it the P36 at 3,600 mm (141.7 in) by 2,150 mm (84.6 in).
What a buyer configures is the head, the version and the magazine. The head is either the THC, with a B axis running -15º/+195º, or the THR, whose A axis runs -45º/+135º. The THC's range is the wider of the two, which gives more approach angles from a single clamping. The version is P Extreme for 5-axis milling or P Multiprocess for 5-axis turning and milling.
Spindle power reaches 84 kW (112.6 hp) and magazines go up to 360 positions, both stated as upper limits. A swing of 3,000 mm against 1,950 mm of height suits work that is wider than it is tall, such as rings, housings and discs. Long shaft-like parts stood on end run out of height first.
Full Specifications
| Parameter | Value |
|---|---|
| Max Swing Diameter | 3,000 mm (118.1 in) |
| Max Part Height | 1,950 mm (76.8 in) |
| Spindle Motor Power | Up to 84 kW (112.6 hp) |
| B Axis Range | -15º/+195º (THC head) |
| A Axis Range | -45º/+135º (THR head) |
| Tool Capacity | Tool magazines up to 360 positions |
| Versions | P Extreme (5-axis milling) / P Multiprocess (5-axis turning and milling) |
Specifications sourced from ibarmia.com — verified 2026-10-03
Strengths & Limitations
Strengths
- 3,000 mm (118.1 in) maximum swing diameter with 1,950 mm (76.8 in) of part height
- Choice of two heads: THC with a -15º/+195º B axis, or THR with a -45º/+135º A axis
- Magazines of up to 360 positions and spindle power of up to 84 kW (112.6 hp)
Limitations
- Part height stops at 1,950 mm (76.8 in); the P36 allows 2,150 mm (84.6 in)
- Turning needs the P Multiprocess version; P Extreme is listed for 5-axis milling only
- Spindle speed, torque and table load are absent from the table, so the 84 kW (112.6 hp) figure cannot be turned into a cutting capability without more data
Best For
Frequently Asked Questions
01
By envelope it is the middle size. The P30 lists 3,000 mm (118.1 in) of swing and 1,950 mm (76.8 in) of part height. The P26 lists 2,600 mm (102.4 in) and 1,750 mm (68.9 in), the P36 3,600 mm (141.7 in) and 2,150 mm (84.6 in). Power and magazine limits do not change between them.
02
Only as the P Multiprocess, which Ibarmia lists for 5-axis turning and milling. The P Extreme is the 5-axis milling version. The 3,000 mm (118.1 in) swing diameter and 1,950 mm (76.8 in) part height are given once for the model and are not broken down by version.
03
The table says up to 84 kW (112.6 hp), which describes the largest spindle offered, not necessarily the one on a base machine. No speed or torque figure accompanies it. Ask for the data sheet of the spindle in the quotation before comparing it with the cuts you plan.
More from Ibarmia
Other 5-Axis Machining Centers
DMG Mori DMU 75 monoBLOCK 2nd Generation
Onsrud F148HM
Makino D800Z 50T
SNK RM-5
