Haco Euromaster 3100-135
This model was not found in Haco's current lineup when we checked on 2026-10-03 . It may be a superseded or older model; the specifications below are as we last recorded them.
Key Specifications
bending force
working length
throat depth
stroke
open height
back gauge axes
How much does the Haco Euromaster 3100-135 cost?
Estimated price range
Our best estimate for a cnc press brake in this class — not a quote from Haco. Configuration moves it a long way.
Overview
The Haco Euromaster 3100-135 is a CNC press brake with a listed bending force of 135 metric tons (1,324 kN) over a working length of 3,100 mm (122 in). Haco's current lineup does not include this model, so this page mainly serves someone weighing up a second-hand machine, and the listed figures should be checked against the machine's own plate and manual.
Throat depth is listed at 400 mm (15.75 in) and open height at 430 mm (16.9 in). The throat figure sets how far a sheet can pass behind the tooling line when the part is longer than the gap between the side frames. The open height limits how tall the punch and die stack can be while still leaving room to take a formed part out.
The back gauge is listed with X and R axes as standard and Z1/Z2 as an option. Without Z1/Z2 the fingers are moved along the bed by hand, which slows parts that are bent at several stations. The control row reads "Delem DA-66T or equivalent CNC controller with 3D simulation", so the control fitted to a particular machine has to be confirmed. Weight is listed at approx. 12,000 kg (26,455 lb).
Full Specifications
| Parameter | Value |
|---|---|
| Bending Force | 135 metric tons (1,324 kN) |
| Working Length | 3,100 mm (122 in / ~10.2 ft) |
| Throat Depth | 400 mm (15.75 in) |
| Stroke | 200 mm (7.87 in) |
| Open Height | 430 mm (16.9 in) |
| Back Gauge Axes | X, R axes standard; Z1/Z2 optional |
| Control System | Delem DA-66T or equivalent CNC controller with 3D simulation |
| Machine Weight | Approx. 12,000 kg (26,455 lb) |
| Stroke Length | 269.24 mm |
Specifications compiled from manufacturer literature and industry references. Not independently verified against a published spec sheet — confirm with the manufacturer or an authorised dealer before making a purchasing decision.
Strengths & Limitations
Strengths
- 135 metric tons (1,324 kN) of listed bending force over a 3,100 mm (122 in) working length
- 400 mm (15.75 in) throat depth for parts that extend past the side frames
- CNC control listed with 3D simulation
Limitations
- Z1/Z2 back gauge axes are optional; only X and R are listed as standard
- The table shows two stroke values that disagree, so the usable stroke has to be measured on the machine
- The control is listed as Delem DA-66T or equivalent, so the unit on a given machine must be confirmed
- At approx. 12,000 kg (26,455 lb), moving it takes rigging and a floor check
Best For
Frequently Asked Questions
01
The listed figures give 135 metric tons (1,324 kN) of bending force and a working length of 3,100 mm (122 in). Whether a job fits depends on material, thickness and die opening, so run the tonnage calculation for the longest and thickest part before relying on these numbers.
02
X and R axes are listed as standard, with Z1/Z2 as an option. A given machine may or may not have the option fitted, so look at the back gauge itself instead of assuming Z1/Z2 are there.
03
Machine weight is listed at approx. 12,000 kg (26,455 lb). Check the floor loading and the lifting plan against that before the machine is moved, and confirm the weight on the machine's plate, since the listed figures are unconfirmed.
