Haas VF-11
Key Specifications
X Travel
Y Travel
Z Travel
Max Spindle
Spindle Taper
Tool Capacity
Overview
The Haas VF-11 is the extra-large 40-taper VMC in the VF lineup, combining 3,048 mm (120 in) of X-travel with 813 mm (32 in) of Y and 762 mm (30 in) of Z. Ten feet of X-travel on a single 40-taper machine puts it in a class where most competitors offer only horizontal boring mills or gantry routers. For shops that need to single-setup a 10-foot part on a conventional VMC platform at 40-taper tooling cost, the VF-11 is the answer.
The table measures 3,048 x 711 mm (120 x 28 in) with five T-slots on 125 mm centers and a 1,814 kg (4,000 lb) load capacity. At 15,150 kg (33,400 lb), the VF-11 is among the heaviest machines in the entire Haas catalog, providing exceptional vibration damping and structural rigidity during long cuts across the full 10-foot span.
The 22.4 kW (30 hp) inline direct-drive spindle runs at 8,100 RPM with 122 Nm (90 ft-lbf) of torque at 2,000 RPM, matching the proven spindle used across the VF family. The optional two-speed gearbox pushes torque to 339 Nm (250 ft-lbf) at 450 RPM for heavy face milling on steel and cast iron. The extended X-axis means X-axis rapids run at 9.1 m/min (360 ipm) rather than the 15.2 m/min (600 ipm) of shorter models — a necessary trade-off for covering 10 feet of travel reliably. Y and Z rapids remain at 15.2 m/min (600 ipm).
The standard 30+1 SMTC with 2.8-second tool-to-tool and 3.6-second chip-to-chip covers most job requirements. An optional 50+1 SMTC is available for tool-intensive programs. Maximum tool length is 406 mm (16 in) from gage line, accommodating the extended-reach tools needed for deep-pocket and long-span work. The NGC control with 15-inch touchscreen, 1 GB program memory, USB, and Ethernet is the same system Haas operators know across every VF machine.
Base price starts around $265,000-$290,000 — a significant step up from the VF-6 but dramatically less than a comparable horizontal boring mill or bridge mill for the same X-travel. For aerospace, defense, energy, and heavy equipment shops that machine one-piece parts or weld fixtures over 8 feet long, the VF-11 removes the need for multi-setup repositioning that introduces tolerance stack-up and handling risk. Specs sourced from Haas Automation published data.
Full Specifications
| Parameter | Value |
|---|---|
| X-Axis Travel | 3,048 mm (120 in) |
| Y-Axis Travel | 813 mm (32 in) |
| Z-Axis Travel | 762 mm (30 in) |
| Spindle Nose To Table Max | 864 mm (34 in) |
| Spindle Nose To Table Min | 102 mm (4 in) |
| Max Spindle Speed | 8,100 RPM |
| Spindle Taper | CT40 / BT40 / HSK-A63 |
| Spindle Motor Power | 22.4 kW (30 hp) |
| Spindle Torque | 122 Nm (90 ft-lbf) @ 2,000 RPM |
| Spindle Torque Gearbox | 339 Nm (250 ft-lbf) @ 450 RPM (optional) |
| Spindle Drive | Inline Direct-Drive |
| Spindle Cooling | Liquid Cooled |
| Tool Capacity | 30+1 SMTC (50+1 optional) |
| Tool To Tool | 2.8 sec |
| Chip To Chip | 3.6 sec |
| Max Tool Diameter | 64 mm (2.5 in) full / 127 mm (5 in) adjacent empty |
| Max Tool Length | 406 mm (16 in) |
| Max Tool Weight | 5.4 kg (12 lb) |
| Table Size | 3,048 x 711 mm (120 x 28 in) |
| Max Table Load | 1,814 kg (4,000 lb) |
| T Slots | 5 slots, 125 mm (4.92 in) center distance |
| Rapid Traverse X | 9.1 m/min (360 ipm) |
| Rapid Traverse Y | 15.2 m/min (600 ipm) |
| Rapid Traverse Z | 15.2 m/min (600 ipm) |
| Max Cutting Feedrate | 9.1 m/min (360 ipm) |
| Max Thrust X | 15,124 N (3,400 lbf) |
| Max Thrust Y | 15,124 N (3,400 lbf) |
| Max Thrust Z | 24,910 N (5,600 lbf) |
| Machine Weight | 15,150 kg (33,400 lb) |
| CNC Control | Haas Next Generation Control (NGC) |
| Coolant Capacity | 360 L (95 gal) |
| Air Requirement | 113 L/min @ 6.9 bar (4 scfm @ 100 psi) |
| Electrical | 220 VAC 3-phase, 70 A (optional 440 VAC, 35 A) |
Specifications sourced from haascnc.com — verified 2026-03-28
Strengths & Limitations
Strengths
- 3,048 mm (120 in) X-travel on a 40-taper VMC platform enables single-setup machining of 10-foot parts without repositioning
- 15,150 kg (33,400 lb) machine mass is among the heaviest in the Haas catalog, providing exceptional rigidity across the full 10-foot X-span
- 40-taper tooling compatibility preserves existing tooling investments without switching to 50-taper
- 3,048 x 711 mm (120 x 28 in) table with 4,000 lb load capacity handles long fixtures, weld assemblies, and multi-part setups
- Base price significantly lower than comparable horizontal boring mills or bridge mills for equivalent X-travel
Limitations
- 9.1 m/min (360 ipm) X-axis rapids add significant cycle time on programs requiring frequent long traverses across the full 10-foot table
- 8,100 RPM spindle is adequate but limiting for high-speed aluminum finishing across long spans
- 33,400 lb shipping weight demands heavy rigging, a reinforced concrete floor, and significant site preparation
- Large footprint requires approximately 30 x 14 feet of dedicated floor space with operator and service clearance
- At this scale, 40-taper clamping force can limit aggressive cutting with very large-diameter tools compared to HBM alternatives
Best For
Frequently Asked Questions
01
Base price starts around $265,000-$290,000. With through-spindle coolant, probing, chip conveyor, gearbox, and 50+1 SMTC, expect $310,000-$350,000. The VF-11 is a specialized machine with a narrower used market than smaller VF models; used examples from 2015-2022 typically sell for $100,000-$180,000.
02
Covering 3,048 mm (10 feet) of travel with a standard ballscrew and servo system requires reduced rapid rates to maintain positioning accuracy and mechanical reliability. Running 1,000 ipm over 10 feet would require much larger drive systems, significantly increasing cost and complexity. The 360 ipm X-rapid is standard for VMCs in this travel class.
03
For flat or prismatic parts that can be fixtured on the table, the VF-11 costs significantly less than most HBMs with comparable X-travel and offers the familiar Haas NGC control. HBMs are better for reaching around all sides of a workpiece, particularly with a rotary table, and typically offer higher spindle power for deep boring. The VF-11 wins on price and setup simplicity for long flat parts.
04
For any shop doing heavy face milling in steel or cast iron across the full table, yes. The gearbox triples torque from 90 to 250 ft-lb at low RPM, letting you run larger face mills at more aggressive feeds. The gearbox adds a modest amount to the base price and is one of the highest-value options on large-frame VF models.
05
At 15,150 kg (33,400 lb), you need a reinforced industrial floor rated for at least 20,000 kg total including the machine, workpiece, and dynamic cutting forces. Most shops installing a VF-11 pour a dedicated machine pad 250-300 mm thick with rebar. Plan for shipping dimensions of approximately 365 x 170 inches when arranging rigging and placement.
Videos
MachinesUsed
MachinesUsed
Concord Machine Tools
Midas Pattern Company Ltd
New England Industrial Machinery
Community Discussions
Troubleshooting and problem-solving — VF-3 and VF-11 problems
Community discussion — Haas VF - Bijur oil pump & what oil do you guys use ...
Pricing and buying discussion — WTS - 2008 Haas VF-11/50 ...
Community discussion — Help measuring a large radius with probe in Haas ...
Community discussion — VF-11 40-Taper Gearbox Noise - CNCzone
Troubleshooting and problem-solving — Problem Alarm 121, Low Lube or Low Pressure - CNCzone
Community discussion — Our latest VF-11 "Improvement" - cnczone.com
Community discussion — Tapping speeds? - CNCzone
Troubleshooting and problem-solving — My friday on the haas vf-11 : r/Machinists - Reddit
Community discussion — Is Haas Really That Bad? : r/Machinists - Reddit
Pricing and buying discussion — Recommendations for CNC VMC : r/Machinists - Reddit
Pricing and buying discussion — Haas cnc machine reliability? : r/Machinists - Reddit
Links to community discussions. Summaries are editorial — visit the original thread for full context.
