KMT Waterjet Streamline SL-VI 100 High-Pressure Intensifier Pump
Key Specifications
motor rating
pressure range deadhead
max flow rate at max pressure 60 hz
length
width
height
How much does the KMT Waterjet Streamline SL-VI 100 High-Pressure Intensifier Pump cost?
Estimated price range
Our best estimate for a cnc waterjet cutting in this class — not a quote from KMT Waterjet. Configuration moves it a long way.
Overview
The KMT Waterjet Streamline SL-VI 100 is a 100 hp (75 kw) high-pressure intensifier pump with a 60,000 psi pressure rating. KMT lists its maximum flow at maximum pressure as 1.88 gpm (7.12 L/min).
That flow figure is the number to size a cutting system around. Every orifice on the table draws from the same 1.88 gpm (7.12 L/min), so the choice is between one large orifice for thick or fast cutting and several smaller ones running side by side. The 60,000 psi figure is given as a deadhead rating, which is the pressure with the cutting head closed and not the pressure while water is flowing.
The cabinet is 84" long, 54" wide and 60" high, and the machine weighs 4,200 lbs. Plan the lift and the floor position before delivery, and leave room around the cabinet to reach the high-pressure end for seal work. The table on this page does not cover electrical supply, cooling water or the hydraulic reservoir, so take those from KMT's installation documents before the site is prepared.
Full Specifications
| Parameter | Value |
|---|---|
| Motor Rating | 100 hp (75 kw) |
| Pressure Range Deadhead | 60,000 psi |
| Max Flow Rate at Max Pressure 60 Hz | 1.88 gpm (7.12 L/min) |
| Length | 84" |
| Width | 54" |
| Height | 60" |
| Machine Weight | 4,200 lbs |
Specifications sourced from kmtwaterjet.com — verified 2026-10-03
Strengths & Limitations
Strengths
- 100 hp (75 kw) motor with 1.88 gpm (7.12 L/min) of flow at maximum pressure
- 60,000 psi deadhead pressure rating
- Cabinet of 84" x 54" x 60" with a listed machine weight of 4,200 lbs, so space and rigging can be planned from the table
Limitations
- Total flow is capped at 1.88 gpm (7.12 L/min), shared by every cutting head on the system
- The pressure rating stops at 60,000 psi
- At 4,200 lbs the pump needs lifting equipment and a floor position decided in advance
Best For
Frequently Asked Questions
01
KMT lists a maximum flow rate of 1.88 gpm (7.12 L/min) at maximum pressure, from a 100 hp (75 kw) motor. That is the total available to all cutting heads together, so add up the flow of every orifice you plan to run and keep the sum below it.
02
Deadhead is the condition where the pump is pressurised but the cutting head is closed, so no water is flowing. KMT gives the pressure range of this pump as 60,000 psi deadhead. Pressure at the nozzle while cutting depends on the orifice in use and on the plumbing between pump and head.
03
The pump is 84" long, 54" wide and 60" high, and the machine weight is 4,200 lbs. Check door openings and the route to the pump's position against those dimensions, and make sure the forklift or crane on site is rated for the weight.
More from KMT Waterjet
KMT Waterjet Streamline SL-V 100
KMT Waterjet Streamline PRO 60 II
KMT Waterjet Streamline PRO-III 60
KMT Streamline PRO CNC Waterjet System
KMT Streamline SL-V 50 Intensifier Pump
Other CNC Waterjet Cutting
WardJet X-2040
Flow EchoJet
Jet Edge X-5 Series
AKS Cutting Systems water-kut X3
Jet Edge Mid Rail Gantry
